Your Best Choice for Furnace and Air Conditioning Repair in Monroeville, PA

I was called to a home to repair a furnace that was not heating. Upon arrival, I found that the flame sensor was not reading a strong signal. I replaced the sensor and cleaned the furnace. The system is now operational.

I was called to a home to repair a furnace condensate pump that was not working. Upon arrival, I found that the condensate pump was overflowing. I removed the check valve and found that the float ball was stuck due to corrosive bleach being used to treat the pump. The customer had already switched to vinegar as advised from another service call. I removed the check valve float ball and the pump is now operational.

was called to a house for no hot water, found the safety switch was tripped, cleaned out burner compartment and tested, system now operational.

The customer complained that the furnace was not heating the living room and other parts of the house well. After evaluating the system, I found that two adjustable dampers in the ductwork were closed to those locations. I opened the dampers and checked the airflow. The rooms are now heating very well.

I was called to a house for no heat. Upon arrival, I found a condensate back up causing issues. I was able to clean out the condensate removal system and now the unit is heating normally.

I was called out to a home for a furnace that was not producing enough heat. Upon arrival, I found that the flame signal was weak, indicating a problem with the furnace. I inspected the furnace and found that the sensor was dirty, causing the flame signal to be weak. I cleaned the sensor and the furnace started working properly. I also checked the air filter and found that it was dirty, so I cleaned it. The homeowner was very happy with the service and thanked me for my help.

I recently completed a boiler inspection for a client. The system was operational and in good working condition. I inspected the boiler, inspected the fuel lines, and checked the combustion chamber for any signs of wear or damage. I also tested the safety controls and made sure that the boiler was operating at the correct pressure.

I recently completed a furnace inspection for a client. The system was operational, and I provided the client with a detailed report of my findings. The client was very satisfied with my work.

I recently completed a job installing a new high-efficiency furnace and hepa filtration system in a residential home. The system is operational and providing the homeowner with comfortable and efficient heating and air conditioning.

I completed a second opinion for a furnace replacement. The customer was informed that the heat exchanger on her furnace was cracked and wanted pricing for replacement. I gladly informed her that i could provide that information, but if she would like, i could evaluate the 10 year old furnace before continuing. After performing a camera inspection with the customer present, we found no cracks or need for replacement. The customer was very relieved and looked forward to future safety inspections.

I recently completed a furnace inspection. The system is operational, and I found no issues with the heating system. I tested the thermostat, checked the ignitor, and tested the burners. I also inspected the flue. I tested the thermostat and the fan, and everything is working correctly. I also checked the electrical connections and everything is working properly. The customer was happy with the service, and I left the job site clean and tidy.

I was called out to a residential home to repair a faulty furnace. Upon arrival, I found that the pressure switch was faulty and needed to be replaced. After replacing the switch, I tested the system and it was operational.

I was called to a home to repair a malfunctioning air conditioner. Upon arrival, I found that the capacitor had failed, causing the system to not operate. I replaced the capacitor and the system was operational again.

The condensate drain was clogged, and I cleared it. I also checked the normal operation of the unit and found that it was working properly.

I was called to a home to repair a leaking water main. Upon arrival, I found that the water main was very old and was leaking. I called for an emergency shut off the water supply to the home and then replaced the main valve. After the repair, I tested the water pressure and found that it was normal. I then cleaned up the area and left the home in good condition.

I was called to inspect an air conditioning unit that was not cooling. After inspection, I found that the air filter was dirty and needed to be replaced. I also noticed that the unit was low on refrigerant. I added refrigerant and the unit is now cooling again.

I was called to inspect an A/C unit that was not cooling. I found that the unit had an ICP air conditioning system. I replaced the capacitor and the unit is now cooling again.

I was called to inspect an AC unit that wasn't cooling. The Lennox AC had a frozen coil. I inspected the unit and found that the coil was frozen due to a refrigerant leak. I recharged the system. I recommended a repair or replacement of the AC unit.

I received a call from a customer who reported that their air conditioner was not cooling. I arrived at the customer's home and found that the condenser needed to be cleaned. I cleaned the condenser and the air conditioner started cooling again.

I was responsible for inspecting, cleaning, and maintaining an air conditioner. I also checked the safety of the air conditioner.

I am a skilled HVAC contractor who recently completed an A/C inspection, air conditioner check, AC safety check, air conditioner cleaning, and A/C maintenance for a customer. I also refilled the Freon in the system.

I recently completed a job that involved inspecting, repairing, and maintaining an air conditioner. The job required me to check the motor, perform a safety test, clean the unit, and perform regular maintenance. I also replaced the air filter and checked the refrigerant levels.

I was hired to install a water heater in a residential home. The job required me to remove the old water heater, install the new one, and connect the gas and water lines. I also had to test the water heater to ensure it was working properly.

I was called to a home to fix a broken air conditioner. Upon inspection, I found that the unit was 40 years old and had a failed flue system. I replaced the failed pieces and inspected the system, which is now operating normally.

I am a highly skilled HVAC contractor professional. I recently completed an A/C inspection, AC safety check, air conditioner cleaning, and A/C maintenance. The system is working great.

I was called to a home to fix an AC unit that wasn't cooling. Upon arrival, I found that the system was low on refrigerant. I recharged the system and now the AC is blowing cold air. The customer was happy to have their AC working again.

I was called to install a water heater in a home. I arrived on time and got to work right away. I removed the old water heater and installed the new one. I made sure that the connections were tight and that the water heater was level. I also tested the water heater to make sure that it was working properly. I cleaned up my work area and left the home in good condition.

I was called to a home to repair a leaking ice maker line that was causing major water damage to the floor and some damage to the cabinets. I found that the valve had been installed incorrectly, causing the line to leak. I replaced the valve and repaired the damage to the floor and cabinets.

I was called to a home to repair a leaking copper line to a refrigerator. Upon inspection, I discovered that the line had been damaged and replaced it.

I am a professional HVAC contractor, and I recently completed a furnace inspection and safety check for a client. This involved inspecting the furnace, checking for any signs of damage or wear, and ensuring that the system was operating safely and efficiently.

I inspected a furnace and confirmed that it was working properly. I also checked the system for safety issues.

I was called to a home to repair a leaking furnace. Upon arrival, I found a rusted furnace and water around it. I removed the leaking flue collector and sealed the surface with RTV. I then tested the system and found no more leaks.

The customer was experiencing issues with their air conditioner. The AC was blowing hot air and the fan motor was not working. I replaced the fan motor and cycled the unit. The AC is now operational.

I am a highly skilled HVAC technician. I recently completed an AC inspection for a client. I cleaned and checked the AC unit, ensuring it was in good working condition.

I was called to a home with an air conditioner that wasn't cooling. I diagnosed the issue as a compressor failure and replaced it. I also recharged the unit and tested it. The system is now operational.

I recently completed a vent and gas line repair job for a client. The job involved replacing a damaged vent and gas line, which required careful disassembly and replacement of the damaged components. I also tested the new line for leaks and ensured that it was properly installed and functioning correctly. The client was very pleased with the work and expressed their satisfaction with my professionalism and attention to detail.

I was called to a home to repair an air conditioner that was low on freon. I diagnosed the issue and replaced the freon, which resolved the problem.

I was called to a home to repair an air conditioner that was not cooling. I found that the system was low on charge and that the unit was not communicating properly with the thermostat. I added 1lb of R410a and a leak stop to the unit and reset the controls. I cycled the unit and the system is operational.

I was called to fix a broken garbage disposal. I removed the old one and installed a new one. The customer was thanked me for my service.

I recently completed a safety inspection for a furnace repair that I repaired. I inspected the furnace to ensure it was safe to operate and that it was not producing any hazardous fumes. I also checked the electrical wiring and gas lines to make sure they were in good condition.

I was called to repair a boiler in a residential home. The boiler was not producing enough heat for the home. I found that the zone valves were leaking and needed to be replaced. I re-piped the zone valves in the garage to replace all three zone valves.

I was called to repair a furnace not heating. I arrived at the customer's home and diagnosed the issue as a faulty blower motor. I replaced the motor and tested the furnace to ensure it was working properly. The customer was happy with the service and thanked me for my help.

I replaced a faulty blower motor.